Door Opener Gear Series

• 

  Door Opener Brass Gear

  The copper gear of the door opener is composed of reducers, gears, rolling bearings, sliding bearings and other parts that need to be lubricated, as well as some other parts. Improving the lubrication efficiency of these parts will improve the safety of production and increase The life of the equipment reduces the labor intensity and improves the economic benefits of the enterprise.
  The copper gear of the door opener refers to a small system formed by combining many gears. There are many gears of different sizes, and all the gears maintain the same rotation speed (linear speed). It is mainly used to transmit torque, change speed and change direction of torque. It is widely used in metallurgical equipment, transmission boxes, etc.

  contact us
• 

  Door Opener Worm

  The sliding coefficient of the tooth root of the worm gear of the door opener is greater than that of the tooth top, and the sliding coefficient of the tooth root of the pinion is greater than that of the tooth root of the large gear. It should be made of harder materials, and its hardness should be dozens of HB higher than that of the big gear in heat treatment. The door opener gear can also be heated along the tooth groove by high frequency induction and quenched on the surface to increase its wear resistance. In the initial work after replacing the new gear, generally only pay attention to whether the work and sound of each part are normal. If it is basically normal, it will be put into use. The running-in and no-load tests are not sufficient, and the intention of the gear running-in cannot be achieved.

  contact us
• 

  Door Opener Worm Gear

  The sliding coefficient of the tooth root of the door opener worm wheel cast steel bevel gear is greater than that of the tooth top, and the sliding coefficient of the small gear tooth root is greater than that of the large gear tooth root. In order to make the tooth root wear of the large and small reduction gears close Even, the pinion gear should be made of harder material, and its hardness should be dozens of HB higher than that of the big gear in the heat treatment. The nylon door opener gear can also be heated and surface quenched along the tooth groove by high-frequency induction to increase its abrasion resistance. In the initial work after replacing the new gear, generally only pay attention to whether the work and sound of each part are normal. If it is basically normal, it will be put into use. The running-in and no-load tests are not sufficient, and the intention of the gear running-in cannot be achieved.

  contact us
• 

  Door Opener Gear

  The sliding coefficient of the dedendum of the door opener gear is greater than that of the tooth top, and the sliding coefficient of the dedendum of the pinion is greater than that of the dedendum of the large gear. It should be made of harder material, and its hardness should be dozens of HB higher than that of the large gear through heat treatment. The pinion can also be heated by high-frequency induction along the tooth groove and quenched on the surface to increase its wear resistance. In the initial work after replacing the new gear, generally only pay attention to whether the work and sound of each part are normal. If it is basically normal, it will be put into use. The running-in and no-load tests are not sufficient, and the intention of the gear running-in cannot be achieved.

  contact us
• 

  Door Opener Iron Gear

  The iron gear of the door opener is composed of reducers, gears, rolling bearings, sliding bearings and other parts that need to be lubricated, as well as some other parts. Improving the lubrication efficiency of these parts will improve the safety of production and increase The life of the equipment reduces the labor intensity and improves the economic benefits of the enterprise.
  The iron gear of the door opener refers to a small system formed by combining many gears. There are many gears of different sizes, and all the gears maintain the same rotation speed (linear speed). It is mainly used to transmit torque, change speed and change direction of torque. It is widely used in metallurgical equipment, transmission boxes, etc.

  contact us
• 

  Door Opener Iron Tooth

  The iron tooth of the door opener is composed of parts that need to be lubricated, such as reducers, gears, rolling bearings, and sliding bearings, as well as some other parts. Improving the lubrication efficiency of these parts will improve the safety of production and increase The service life of the equipment is extended, the labor intensity is reduced, and the economic benefits of the enterprise are improved.
  The door opener iron tooth refers to a small system formed by a combination of many gears. There are many gears of different sizes, and all the gears maintain the same rotation speed (linear speed). It is mainly used to transmit torque, change speed and change direction of torque. It is widely used in metallurgical equipment, transmission boxes, etc.

  contact us